Warning: Some posts on this platform may contain adult material intended for mature audiences only. Viewer discretion is advised. By clicking ‘Continue’, you confirm that you are 18 years or older and consent to viewing explicit content.
For next time there are little wall repair kits from Bunnings which include special netting with a slightly sticky back. You trim it to size with a little overlap at the edges and stick it over the hole. It gives the layers of putty something to grab onto.
Apply the putty in really thin layers with the spatula scraping it as smooth as possible, letting it fully dry and sanding it flush before the next one. Sand it really flat with sandpaper around a foam sanding block because doing it with sandpaper on your fingers can leave it uneven.
For the paint it really helps to cut a 50c piece sized layer of paint from somewhere really hard to notice of the same colour (use a razorblade and kind of slice at an angle) and get it put through the paint matching machine at Bunnings.
Use a roller not a brush because you don’t want visible brushmarks. Bunnings sell little disposable rollers and paint trays. Do really thin layers too with drying between, feathering the edges out with the last tiny (barely any) bit of paint left on the roller each time so it’s harder to see a sudden transition. Putty and paint the sneaky spot you nicked the chip from too.
The paint colour you got mixed may differ slightly from the main spot due to different rates of fading (ie if the sample paint chip was taken from inside a wardrobe) but do your best, let it fully dry and rub a dusty rag over it at the end so it doesn’t look too new.
No worries. I just used the mesh because it was a larger hole and that really helped to have a stable base for applying thinner smoother layers.
Personally if it was me? I’d just try and sand it as flat as possible, see if I could get it flat. You might need a rougher grade of sandpaper and a sanding block if it’s slow going. Then smooth it with finer. Then paint the spot in a few thin layers drying in between - if it’s still looking very obvious you might then choose to paint the whole door.
I’m not a professional though. Just a renter that had to do this a couple of times
For next time there are little wall repair kits from Bunnings which include special netting with a slightly sticky back. You trim it to size with a little overlap at the edges and stick it over the hole. It gives the layers of putty something to grab onto.
Apply the putty in really thin layers with the spatula scraping it as smooth as possible, letting it fully dry and sanding it flush before the next one. Sand it really flat with sandpaper around a foam sanding block because doing it with sandpaper on your fingers can leave it uneven.
For the paint it really helps to cut a 50c piece sized layer of paint from somewhere really hard to notice of the same colour (use a razorblade and kind of slice at an angle) and get it put through the paint matching machine at Bunnings.
Use a roller not a brush because you don’t want visible brushmarks. Bunnings sell little disposable rollers and paint trays. Do really thin layers too with drying between, feathering the edges out with the last tiny (barely any) bit of paint left on the roller each time so it’s harder to see a sudden transition. Putty and paint the sneaky spot you nicked the chip from too.
The paint colour you got mixed may differ slightly from the main spot due to different rates of fading (ie if the sample paint chip was taken from inside a wardrobe) but do your best, let it fully dry and rub a dusty rag over it at the end so it doesn’t look too new.
Source: Renter
Thanks friend. I asked the Bunnings guy what to use and he recommended just the filler and not the kit so I went with that.
From here, would the best option be to sand it, re putty it, re sand till flat, then paint entire door with roller or just the patch?
No worries. I just used the mesh because it was a larger hole and that really helped to have a stable base for applying thinner smoother layers.
Personally if it was me? I’d just try and sand it as flat as possible, see if I could get it flat. You might need a rougher grade of sandpaper and a sanding block if it’s slow going. Then smooth it with finer. Then paint the spot in a few thin layers drying in between - if it’s still looking very obvious you might then choose to paint the whole door.
I’m not a professional though. Just a renter that had to do this a couple of times