Installed this valve the very first time I changed my oil. It makes it so easy. And when I buy new oil filters the guys at the auto shop give me wild looks when I tell them I don’t need the crush washer. :D

  • BillMurray@lemmy.world
    link
    fedilink
    English
    arrow-up
    1
    ·
    1 year ago

    Hopefully yours doesn’t leak… Woke up one morning to oil all over my garage, the valve was closed but I guess it failed. Replaced it with the traditional bolt and washer, never had a problem since. Just get one of those magnetic oil change tools to take the drain bolt off.

  • rikonium@discuss.tchncs.de
    link
    fedilink
    English
    arrow-up
    1
    ·
    1 year ago

    I had one, still have it in my bag and it’s been terrific. The tubing and valve combo eliminated splash, spill, shoving my hand up there, etc.

    The bad news is that it was just a smidge too low and I tweaked it off-road - I do have a skid plate but the bottom was pretty much in-line with the top of the plate so too close.

    One oil pan later, I’m back with the bolt but only by necessity. I think I’ll put a valve on my SO’s cousin’s Honda. The drain hole is horizontal on that one.

  • Skanky@lemmy.world
    link
    fedilink
    English
    arrow-up
    1
    ·
    1 year ago

    I’ve never used a crush washer in my life. Are they really necessary? I’ve never had an issue with leaky oil?

    • Marcumas@lemmy.world
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      It’s not like all your oil will drain out if you don’t use them, but they help seal between the pan and the plug, helps stop you from over tightening the drain bolt, and makes it a little easier to get the bolt back off for the next oil change.

      • Skanky@lemmy.world
        link
        fedilink
        English
        arrow-up
        0
        ·
        1 year ago

        I always use a torque wrench when tightening, so there is no issue with over tightening.

        Removing the oil pan nut has never really been an issue, likely due to the above statement.

        • rusty brown@midwest.social
          link
          fedilink
          English
          arrow-up
          0
          ·
          1 year ago

          i have changed oil in vehicles probably 30 times at this point. last year for some dumbass reason i decided to start using a torque wrench to tighten.

          looking at the specs for my foreign, i did not look at the correct column on the page for ft/lbs or Nm… did not double check… and ended up fucking stripping the bolt threads on the oil pan!!!

          had a hell of a time removing the bolt, but there were enough good threads that i could drill out what i cross threaded and still attach the bolt… i did not have to have an oil pan replacement… and no drips or leaks… i count myself extremely, extremely stupid and lucky.

          • Skanky@lemmy.world
            link
            fedilink
            English
            arrow-up
            1
            ·
            1 year ago

            Ooof. That hurts.

            If it makes you feel any better, one time I accidentally drained my transmission fluid because I took off the wrong plug! That was a rather costly mistake as you can’t simply add transmission fluid to fix it. You have to flush and bleed the lines, and I did not have all the right equipment. Had to have my car towed from my driveway to the shop! Oops.

    • pelotron@midwest.socialOP
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      Y’all are about to scare me straight!

      To answer your question, it’s less about time savings and more about cutting out the mess. When 0w20 oil hits the pan that stuff splatters everywhere.