Let’s hear it. No project too big or too small.

  • nyan@lemmy.cafe
    link
    fedilink
    arrow-up
    5
    ·
    1 year ago

    Was going to try to get the rust off my father’s crappy old hand plane (since restoring it would get me out of having to buy a hand plane of my own for now), but it doesn’t look like I’m going to get that far this week. Spent a couple of hours moving books around to clear some shelf space instead.

  • Seathru@beehaw.org
    link
    fedilink
    arrow-up
    5
    ·
    1 year ago

    I’m going to attempt to fix my truck’s air conditioning. Of course it waited until the weather was sweltering hot to stop working. I know just enough about refrigerant systems to be dangerous, wish me luck!

    If that’s successful and/or doesn’t take all weekend, I’m going to try to build some temporary screening around my tiny back porch to give me somewhere to sit outside away from the mosquitos.

      • Seathru@beehaw.org
        link
        fedilink
        arrow-up
        3
        ·
        1 year ago

        Yeah, that side is more my speed, too. I built an arduino based compressor controller a few years ago when that went out. But this is something internal (high side pressure pegging the gauge 30 seconds after the compressor engages).

        Took it by a friends shop to get it evacuated today and they agreed that my amateur assessment (dryer and expansion valve) was where they would start first. So I’ve got a bit more confidence going into it. Fingers and toes crossed I don’t find a bunch of metal inside.

    • jarfil@beehaw.org
      link
      fedilink
      arrow-up
      1
      ·
      1 year ago

      The one I have doesn’t fit through the strainer, I’ll try to locate a thinner one, or some of those hair removal ziptie lookalikes (it likely isn’t hair stuck down there, but who knows).

  • upstream@beehaw.org
    link
    fedilink
    arrow-up
    4
    ·
    1 year ago

    I live in a rented apartment and since we moved in one of the (IKEA) bedroom closets has been horrible built.

    The landlord commented that the previous tenant had taken them down, but put them back together when they moved out.

    Didn’t look to closely but it was always a bit wobbly. In part thanks to covid we’ve ended up living here longer than planned and the closet was now almost tipping over, so I decided to take action.

    Just disassembled it and apart from the back plates being taped together and held in with about 6 nails each, three of which was at the bottom, the upper shelf turned out to not be from this closet.

    It has a label from IKEA and says it’s a kitchen shelf.

    Took out the tape measure and sure enough. It’s 5mm to wide, and at least 3mm to deep.

    Too late to do anything about it now, it’s 10’o clock, but it amazes me at the shit people do.

    No wonder the cabinet doors aligned poorly and all.

  • jarfil@beehaw.org
    link
    fedilink
    arrow-up
    4
    ·
    1 year ago

    Trying to fix a slow bathtub drain.

    It’s got one of those flexible ribbed pipes that keeps holding onto everything, and whoever installed the bathtub had the amazing idea of fully encasing it in brick and large tiles, with no access left to replace the pipe. To add insult to injury, the pipe is attached to the bathtub by a single screw going through a metal strainer, so no way to properly shove in a pipe cleaner without it coming detached and falling under the bathtub… inside the encased part; even if I managed to fish it out afterwards, no way it’s going to match the gasket again. The toilet is also so close to it, that even to try breaking the tile and brick to get to the pipe, one would have to remove the toilet first.

    I’ve poured in some “gel drain cleaner”, left it for a while, washed it out, and some plunger action seemed to move some stuff around, but it was still slow. Poured some caustic soda, which outgassed pretty nicely, and the plunger worked some more, but I’d say it’s still less than 50% there.

    I’m torn as to what to try next, whether some HCl, bleach, or sulfuric, but the strainer is metal and I don’t want to make it look worse than it already does. Could try more of the gel and/or soda, but I think they might’ve already done all they were to do.

      • jarfil@beehaw.org
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        It’s and apartment, so that would require access from the common collector. It is possible, some neighbors did it (to locate a leak they caused by DIY “re-tiling” the bathroom with a jackhammer, not kidding), but it takes a long snake to reach even the bottom floor.

        For now at least it drains. I’ll try and locate a thinner snake, or some of those “hair removal” ziptie lookalikes.

  • TheOtherJake@beehaw.org
    link
    fedilink
    arrow-up
    4
    ·
    1 year ago

    Should be ripping out Windows and getting Fedora Workstation working on a new machine. I’ll probably start working on installing the AI tools I used to justify the new rig. I’m halfway thinking about modifying my laptop bed stand to add more cooling capacity built in, but it kinda depends on how hot it gets with the GPU at full tilt.

    I also need to make some progress getting my desk/hobby electronics workstation back to useful conditions and reinstall all of my lighting.

  • kbyanyname@beehaw.org
    link
    fedilink
    arrow-up
    4
    ·
    1 year ago

    Trying to fix a slow leak in a toilet, likely, but the main project is patching a gap in the ceiling where a vent fan doesn’t quite fit

  • shoveljockey@kbin.social
    link
    fedilink
    arrow-up
    4
    ·
    1 year ago

    I’m still building the addition to my wood framed green house, still have a couple of weekends to go till its done.

  • Fauxreigner@beehaw.org
    link
    fedilink
    arrow-up
    3
    ·
    edit-2
    1 year ago

    Working on building a modern style barn door, although I doubt I’ll be able to paint it this weekend.

  • The_Sasswagon@beehaw.org
    link
    fedilink
    arrow-up
    3
    ·
    1 year ago

    Starting the refinish job on our front porch. Got my broom and sander and some dry weather in the forecast, hopefully it’ll be finished before the next storm rolls through!

  • Kajo [he/him] 🌈@beehaw.org
    link
    fedilink
    arrow-up
    3
    ·
    1 year ago

    I’m in the process of destroing an old, out of service fireplace, to rebuild a fake one with an electric radiator.

    The chimney hadn’t been swept before it was taken out of service, and now I know how much I hate tallow.

  • anarchism@beehaw.org
    link
    fedilink
    arrow-up
    3
    ·
    1 year ago

    was going to make a small garden in a wood box on the deck of my apartment, but its getting unusually hot i think i’ll put it off for a little longer