When I was 15, my dad purchased me a plaster saw (still have it) and handed me his drill.
Then told me to make it look neat, but “don’t fuck up because your mother will kill us both”.
I ran about 4 network points through the house.
Nothing like fear to produce a 100% perfect finish 😉
And then there’s me who just screwed up installing a new door knob. I stripped the threads on the screws cause I used the wrong size screws drilling. Now if the new knob fails in the future, I need to buy a new door lmao
If it’s a wooden door that you’re screwing into, dab some match sticks with a little bit of liquid nails and gently hammer them into the stripped-out screw hole, and cut them flush with the hole. Once the glue dries, you can drive the screw back into the matches and it’ll have enough wood to bite into.
assuming liquid nails means molten metal, I don’t think that’s easily accessible in most homes
you can buy liquid nails at like any home depot type of store
Is it a US thing?
I’m tempted to do this, do you have any tips?
If you can, re-use existing sockets! Old telephone or antenna lines can work! You tie the cable to the end of the old cable and pull it through the existing PVC pipe.
Go ahead and pull em in the wall! Don’t be scared. Worst case the world is ending anyways
Well that’s reassuring
For me it was like
Join forces and do link aggregation for double the speeds.
A tale as old as time. Before Ethernet cables we were running phone extension cables through the house to connect up the modem to the only phone jack.
I did this for every device in my house. used flat ethernet cable and just fished it under the carpets. Was significantly cheaper than trying to make wireless reach the other side of the house.
Flat ethernet cable
What?!! I did not know this existed!!
You can also buy devices you plug into the wall and route your network through your power network. Used them to give my detached garage wifi. Works pretty well.
Based on my research, you get the speed of 2.4 ghz wireless (which while it works, it could be better) with the inconvenience of having to use a cable. Performance also depends on wire insulation, which often isn’t built for running PLC. However, you can’t beat the “plug-and-play” of wired there, which might be attractive.
I’d recommend getting a mesh router setup, gives you 5ghz wireless over the whole house (assuming proper setup), and some mesh points support wired output (effectively having a wireless bridge)
Can be unreliable though based on what else is on the circuit. Had a portable ac that completely took my power line ethernet connection out whenever it ran.
I had to buy carpets to hide the cable under them when running across the floor. Only exposed parts go through the doorways, and the wife complains about them. Well, I am not complaining about our craptastic wifi anymore.
If you own your house you could learn to pull cable and how to do punchdowns. It’s not a super difficult job. That way you could impress the lady of the house with your technical skills while also hiding the mess.
I’d be careful giving broad advice like this.
In my country (Australia) it’s illegal to run cabling yourself unless you’re a registered cabler.
Even for an Ethernet cable? Surely not.
I seem to remember that yes, it was even for low voltage data cabling.
Not that I would imagine anyone’s enforcing it strongly
I think the enforcement would come with insurance when your house burns down, they can point at “unlicensed” cables
Would they be able to prove it wasn’t installed by a licensed contractor? Ok, if you have it installed legally then you’ll likely have an invoice/receipt, but if you lose it that doesn’t mean the cable is illegal. So if you did it yourself, how would they know it’s not just a case of a missing invoice?
I’m not saying it would go anywhere, but with how scummy insurance companies are they might try it. Still, it’s a bullshit law
Even low voltage? That’s kinda crazy to me.
I’m sorry you live in authoritariansville.
You could just use 2 Ethernet Over Power adaptors (not to be confused with power over ethernet).
After all, it’s not as if the powerlines aren’t already installed at home and connect all power plugs with all other power plugs.
This isn’t even new: I’ve been using this solution for about a decade, back when it could do a mere 20Mb/s (which was still way faster than my Internet connection could handle back then ;))
Unless having a 500Mb/s limit on bandwith is somehow unacceptable when you could have Gigabit ethernet. Then again, why not fibre all the way ;)
I always wonder if I’m introducing bad latency by running a 100 ft ethernet cable.
Then I remind myself it’s the speed of light.